25. High Performance Anionic Softener Flakes
For Cotton , Linen, Fabrics Hydrophilic Finishing
Chemical
Composition
Special derivative of fatty
acid compound
Technical
Specification
Appearance:
pale yellow flakes
PH value: 6~8(5-10% solution)
Ionicity: anionic
Properties
Good
hydrophilic, antistatic and low yellowing properties , no influence on
whiteness
Impart very
soft, Smooth and full handle to fabric
Compatible with
anionic and nonionic auxiliaries except cationic auxiliary
Dissolving
Method
Temperature
raising : Add the flakes in water(room temperature )gradually in the proportion
of 5-10%, stir them and heat up to ( 65~75℃ ) and stir them for 30-60 mins again
until the flakes become even paste, then cool it down.
High
temperature :Add the flakes in water ( 65~75℃) gradually in the proportion of 5-10%,
stir them for
30-60 mins again until the flakes become even paste, then cool it down.
Field of
Application
Applied to
softening finishing and hydrophilic finishing of all kinds of fibres ,
especially for cotton , linen and their blended fabrics
Application
Padding: Dosage: 20-30g/L (10%
solution) Temperature: 30-40℃
Process: one dip and one pad or two dips and two pads
Dipping: Dosage: 3-8%(o.w.f)(10%
solution) Liquor ratio: 1:10-15
Temperature: 40-50℃
Time: 30min
26. Anionic Softener Compatible With
Nonionic Auxiliary AT For Fibres Softening Finishing
Chemical
Composition
Special derivative of fatty
acid compound
Properties
Impart very soft, Smooth and full handle to fabric
Good hydrophilic, antistatic and low yellowing properties , no
influence on whiteness
Compatible with anionic and nonionic auxiliaries except cationic
auxiliary
Technical
Specification
Appearance: pale yellow flakes
PH value: 6~8(5-10% solution)
Ionicity: anionic
Dissolving Method
Temperature
raising : Add the flakes in water(room temperature )gradually in the proportion
of 5-10%, stir them and heat up to ( 65~75 ْC ) and stir them for 30-60
mins again until the flakes become even paste, then cool it down.
High
temperature :Add the flakes in water ( 65~75 ْC) gradually in the proportion
of 5-10%,
stir them for
30-60 mins again until the flakes become even paste, then cool it down.
Field of
Application
Applied to
softening finishing and hydrophilic finishing of all kinds of fibres ,
especially for cotton , linen and their blended fabrics
Application
Padding: Dosage: 20-30g/L(10%
solution) Temperature: 30-40 ْC
Process: one dip and one pad or two dips and two pads
Dipping: Dosage: 3-8%(o.w.f)(10%
solution) Liquor ratio: 1:10-15
Temperature: 40-50 ْC
Time: 30min
27. Low Yellowing Anionic Softeners Flakes,
Hydrophilic Fabric Softener Flake
Chemical
Composition
Special derivative of fatty
acid compound
Technical
Specification
Appearance: pale yellow flakes
Ionicity: anionic
PH value : 6~8 (5-10% solution)
Dissolving
Method
Temperature
raising : Add the flakes in water(room temperature )gradually in the proportion
of 5-10%, stir them and heat up to ( 65~75 ْC ) and stir them for 30-60
mins again until the flakes become even paste, then cool it down.
High
temperature :Add the flakes in water ( 65~75 ْC) gradually in the proportion
of 5-10%,
stir them for
30-60 mins again until the flakes become even paste, then cool it down.
Properties
Impart very
soft, Smooth and full handle to fabric
Good
hydrophilic, antistatic and low yellowing properties , no influence on
whiteness
Compatible with
anionic and nonionic auxiliaries except cationic auxiliary
Field of
Application
Applied to
softening finishing and hydrophilic finishing of all kinds of fibres ,
especially for cotton , linen and their blended fabrics
Application
Padding: Dosage: 20-30g/L(10%
solution) Temperature: 30-40 ْC
Process: one dip and one pad or two dips and two pads
Dipping: Dosage: 3-8%(o.w.f)(10%
solution) Liquor ratio: 1:10-15
Temperature: 40-50 ْC
Time: 30min
28. Hydrophilic Softener, Anionic Softener
Flakes For Cotton, Linen, Blended Fabrics
Chemical
Composition
Special derivative of fatty
acid compound
Technical
Specification
Appearance: pale yellow flakes
PH value: 6~8(5-10% solution)
Ionicity: anionic
Dissolving Method
Temperature
raising : Add the flakes in water(room temperature )gradually in the proportion
of 5-10%, stir them and heat up to ( 65~75 ْC ) and stir them for 30-60
mins again until the flakes become even paste, then cool it down.
High
temperature :Add the flakes in water ( 65~75 ْC) gradually in the proportion
of 5-10%,
stir them for
30-60 mins again until the flakes become even paste, then cool it down.
Properties
Impart very soft, Smooth and full handle to fabric
Good hydrophilic, antistatic and low yellowing properties , no
influence on whiteness
Compatible with anionic and nonionic auxiliaries except cationic
auxiliary
Field of Application
Applied to
softening finishing and hydrophilic finishing of all kinds of fibres ,
especially for cotton , linen and their blended fabrics
Application
Padding: Dosage: 20-30g/L (10%
solution) Temperature: 30-40 ْC
Process: one dip and one pad or two dips and two pads
Dipping: Dosage: 3-8% (o.w.f) (10%
solution) Liquor ratio: 1:10-15
Temperature: 40-50 ْC
Time: 30min
29. Anionic Softener Flakes Textile
Chemicals For Fibres Softening / Hydrophilic Finishing
Chemical Composition
Special derivative of fatty
acid compound
Technical
Specification
Appearance: pale yellow flakes
PH value: 6~8(5-10% solution)
Ionicity: anionic
Dissolving Method
Temperature
raising : Add the flakes in water(room temperature )gradually in the proportion
of 5-10%, stir them and heat up to ( 65~75 ْC ) and stir them for 30-60
mins again until the flakes become even paste, then cool it down.
High
temperature :Add the flakes in water ( 65~75 ْC) gradually in the proportion
of 5-10%,
stir them for
30-60 mins again until the flakes become even paste, then cool it down.
Properties
Impart very
soft, Smooth and full handle to fabric
Good
hydrophilic, antistatic and low yellowing properties , no influence on
whiteness
Compatible with
anionic and nonionic auxiliaries except cationic auxiliary
Field of
Application
Applied to
softening finishing and hydrophilic finishing of all kinds of fibres ,
especially for cotton , linen and their blended fabrics
Application
Padding: Dosage: 20-30g/L (10%
solution) Temperature: 30-40 ْC
Process: one dip and one pad or two dips and two pads
Dipping: Dosage: 3-8% (o.w.f) (10%
solution) Liquor ratio: 1 : 10-15
Temperature: 40-50 ْC
Time: 30min
30. Pale Yellow Anionic Softener Flakes,
Textile Softener Flake For Blended Fabrics
Chemical Composition
Special derivative of fatty acid
compound
Technical Specification
Appearance: pale yellow flakes
PH value: 6~8(5-10% solution)
Ionicity: anionic
Dissolving
Method
Temperature
raising : Add the flakes in water(room temperature )gradually in the proportion
of 5-10%, stir them and heat up to ( 65~75 ْC ) and stir them for 30-60
mins again until the flakes become even paste, then cool it down.
High
temperature : Add the flakes in water ( 65~75 ْC) gradually in the proportion
of 5-10%,
stir them for
30-60 mins again until the flakes become even paste, then cool it down.
Properties
Impart very
soft, Smooth and full handle to fabric
Good
hydrophilic, antistatic and low yellowing properties , no influence on
whiteness
Compatible with
anionic and nonionic auxiliaries except cationic auxiliary
Field of
Application
Applied to
softening finishing and hydrophilic finishing of all kinds of fibres ,
especially for cotton , linen and their blended fabrics
Application
Padding: Dosage:20-30g/L (10%
solution) Temperature: 30-40 ْC
Process: one dip and one pad or two dips and two pads
Dipping: Dosage:3-8% (o.w.f) (10%
solution) Liquor ratio: 1:10-15
Temperature: 40-50 ْC
Time: 30min
